Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
DIY OEM Scuff Plate Installation
07-22-2013, 12:20 PM
Post: #1
DIY OEM Scuff Plate Installation
For those planning to DIY install their Scuff plates. Hope this helps. Around 10-15 minutes installation time.

Items needed:
- OEM Scuff Plates
[Image: 9340104610_5fb2625ffa_z.jpg]

- Microfiber cloths, Ruler, Masking Tape, Cutter and Isopropyl alcohol
[Image: 9340117434_ac2543ae6f_z.jpg]

Installation steps:
1. Clean the installation area using the microber cloths with isopropyl alcohol to remove any oil/film that will compromise adhesion.
[Image: 9340027836_ca6507c686_n.jpg] [Image: 9340025654_3b49fc13ac_n.jpg]

2. For the front scuff plates, measure 70mm of masking tape and stick it as seen on the photo. This will serve as guide for alignment (same measurement as indicated on the installation manual). Re-use the same tape on the other side to save time.

[Image: 9337247383_74fd6eef99_z.jpg]

3. Remove the double-sided tape covers in the back of the scuff plates. Before putting the scuff plates in place, make sure to wipe the installation area with the adhesion pack. Don't throw this away as you will need this on the remaining areas. Align the scuff plate as shown.

[Image: 9340031824_65b4e70611_z.jpg]

4. For the rear scuff plates, measure 10mm of masking tape and stick it as seen on the photo. This will serve as guide for alignment (same measurement as indicated on the installation manual). Re-use the same tape on the other side to save time.

[Image: 9337243353_fa880cf73f_z.jpg]

5. Remove the double-sided tape covers in the back of the scuff plates. Before putting the scuff plates in place, make sure to wipe the installation area with the adhesion pack.

[Image: 9340025654_3b49fc13ac_z.jpg]
[Image: 9337237107_a949fef853_z.jpg]

[Image: 14391356808_7fcff1e4d6_m.jpg]
Find all posts by this user
Like Post Quote this message in a reply
07-22-2013, 05:33 PM
Post: #2
RE: DIY OEM Scuff Plate Installation
eto bibili din ako nito...salamat joseph!
Find all posts by this user
Like Post Quote this message in a reply
07-22-2013, 08:00 PM
Post: #3
RE: DIY OEM Scuff Plate Installation
Ganda talaga ng scuff plates sir! Thanks sa detailed procedure, malaking bagay ho ito... :-)

[Image: mphfrontshortwhite2_zpse38cfcaa.jpg]
Find all posts by this user
Like Post Quote this message in a reply
07-23-2013, 07:10 AM
Post: #4
RE: DIY OEM Scuff Plate Installation
ang gusto ko ilagay sa mirage ko ay yung rubber na ginagawa ding mat especially ng mga jeepney at tricycle. yung parang swelas ng tsinelas.

pag kasi scuff plates nakakapanghinayang din magasgas, ang mahal pa.

para may tapakan ang anak ko pag sumasampa sa kotse nang hindi masakit sa bulsa
The following 1 user Likes Deobulakenyo's post:
Sepphiroth

Savannah White, GLX-CVT (Mitsumi)
[Image: mirage-white.png]
Find all posts by this user
Like Post Quote this message in a reply
07-23-2013, 08:41 AM
Post: #5
RE: DIY OEM Scuff Plate Installation
^^Sir Deo
sakin naman problema ko halos after cleaning, yung mga tapakan na plastic na black sa floor namumuti na agad
lalo na yun sa likod na part, parang lagi siya ntatapakan

@brewgemi
ngayon alam ko na bakit may plastic cover yung mga sahig mo sa likod.. ano kaya permanent solution dito?.
errr
Find all posts by this user
Like Post Quote this message in a reply
07-23-2013, 10:26 AM
Post: #6
RE: DIY OEM Scuff Plate Installation
(07-23-2013 08:41 AM)vanityQ Wrote:  ^^Sir Deo
sakin naman problema ko halos after cleaning, yung mga tapakan na plastic na black sa floor namumuti na agad
lalo na yun sa likod na part, parang lagi siya ntatapakan

@brewgemi
ngayon alam ko na bakit may plastic cover yung mga sahig mo sa likod.. ano kaya permanent solution dito?.
errr

sir baka wax residue yan or maybe armor all?

Savannah White, GLX-CVT (Mitsumi)
[Image: mirage-white.png]
Find all posts by this user
Like Post Quote this message in a reply
07-23-2013, 11:38 AM
Post: #7
RE: DIY OEM Scuff Plate Installation
(07-23-2013 08:41 AM)vanityQ Wrote:  ^^Sir Deo
sakin naman problema ko halos after cleaning, yung mga tapakan na plastic na black sa floor namumuti na agad
lalo na yun sa likod na part, parang lagi siya ntatapakan

@brewgemi
ngayon alam ko na bakit may plastic cover yung mga sahig mo sa likod.. ano kaya permanent solution dito?.
errr


hahaha! OC ako sa mga plastic parts bro eh haha! inisip ko nga plastidip bro Daniel P. or yung 3M anti-Slip tape! 4

BTT: Nice Diy sir! 1
Like Post Quote this message in a reply
07-23-2013, 12:01 PM
Post: #8
RE: DIY OEM Scuff Plate Installation
teka ano bang plastic na tapakan yang sinasabi ni boss ragemi?

wala yata kaming ganyan?
The following 1 user Likes Deobulakenyo's post:
PuertoPrincesa

Savannah White, GLX-CVT (Mitsumi)
[Image: mirage-white.png]
Find all posts by this user
Like Post Quote this message in a reply
07-23-2013, 12:03 PM
Post: #9
RE: DIY OEM Scuff Plate Installation
@sir Deo
yun malapit sa scuff plates, yung ipitan ng carpet, floor railing ata tawag doon?
Find all posts by this user
Like Post Quote this message in a reply
07-23-2013, 12:04 PM
Post: #10
RE: DIY OEM Scuff Plate Installation
(07-23-2013 12:03 PM)vanityQ Wrote:  @sir Deo
yun malapit sa scuff plates, yung ipitan ng carpet, floor railing ata tawag doon?

ah. baka nga napapahiran ng wax/chemicals. ako kasi damp cloth pinampupunas ko dun e.

Savannah White, GLX-CVT (Mitsumi)
[Image: mirage-white.png]
Find all posts by this user
Like Post Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)

This forum uses Lukasz Tkacz MyBB addons.