[gls2001]

Walang rubberized layer. Yung double tape ang pinakacushion plus yung rubber sa gilid.

The following 1 user Likes gls2001's post: Deobulakenyo

[viperx]

(07-23-2013 08:41 AM)vanityQ Wrote:  ^^Sir Deo
sakin naman problema ko halos after cleaning, yung mga tapakan na plastic na black sa floor namumuti na agad
lalo na yun sa likod na part, parang lagi siya ntatapakan

@brewgemi
ngayon alam ko na bakit may plastic cover yung mga sahig mo sa likod.. ano kaya permanent solution dito?.
errr

Saken sir bumili ako ng CF sticker at yun dinikit ko dyan. Napansin ko din na may gasgas lalo na pag sumasakay yung anak ko..

[carnage08]

pics nga dre, nakalimutan mo ipakita sakin yan kanina. tsk tsk

[enterbay]

ano ba ibang cheap alternative sa scuff plate? pwede kaya vinyl sticker?

[viperx]

(01-25-2014 11:04 PM)carnage08 Wrote:  pics nga dre, nakalimutan mo ipakita sakin yan kanina. tsk tsk

Pre eto yun pics oh.. Next ko yun sa HU side plastic.

[Expired]

(01-26-2014 12:11 AM)enterbay Wrote:  ano ba ibang cheap alternative sa scuff plate? pwede kaya vinyl sticker?

3M Non Slip Tape Anti Skid Adhesive pwede....

The following 3 users Like Expired's post: viperx, Sepphiroth, Andz5

[Misteri]

(07-22-2013 12:20 PM)gls2001 Wrote:  For those planning to DIY install their Scuff plates. Hope this helps. Around 10-15 minutes installation time.

Items needed:
- OEM Scuff Plates


- Microfiber cloths, Ruler, Masking Tape, Cutter and Isopropyl alcohol


Installation steps:
1. Clean the installation area using the microber cloths with isopropyl alcohol to remove any oil/film that will compromise adhesion.


2. For the front scuff plates, measure 70mm of masking tape and stick it as seen on the photo. This will serve as guide for alignment (same measurement as indicated on the installation manual). Re-use the same tape on the other side to save time.



3. Remove the double-sided tape covers in the back of the scuff plates. Before putting the scuff plates in place, make sure to wipe the installation area with the adhesion pack. Don't throw this away as you will need this on the remaining areas. Align the scuff plate as shown.



4. For the rear scuff plates, measure 10mm of masking tape and stick it as seen on the photo. This will serve as guide for alignment (same measurement as indicated on the installation manual). Re-use the same tape on the other side to save time.



5. Remove the double-sided tape covers in the back of the scuff plates. Before putting the scuff plates in place, make sure to wipe the installation area with the adhesion pack.

same din sa G4 yung measurement sir @gls2001 thanks so much sa DIY!

[keight]

(01-26-2014 10:02 AM)Ragemi Wrote:  

(01-26-2014 12:11 AM)enterbay Wrote:  ano ba ibang cheap alternative sa scuff plate? pwede kaya vinyl sticker?

3M Non Slip Tape Anti Skid Adhesive pwede....

sir, hindi po ba kaya makaka-gasgas sa pinto ng sasakyan, kung ganyan ang gagamitin?
may nakita akong yellow and black design na ganyang tape / adhesive.. )

[Andz5]

afaik nope di yan makakagas gas ,malaki yun space in between ng door and nung mismong pwesto na paglalagyan nyan afaik nasubukan ko na yan sa doors ko sa isang car namin oks namn , non slip pa

[ianxxxchua]

if you really want budget meals, bili po kayo ng Black Matte Sticker or Carbon Fiber Sticker then yun yung idikit po ninyo. tapos lagyan nalang ng maliit na ralliart sticker, voila may scuff plates na.

The following 2 users Like ianxxxchua's post: monsac, keight